PROFITEST INTRO

Tester for DIN VDE 0100-600 / IEC 60364.6

Universal, handy and rugged test instrument for performing all measurements for testing the effectiveness of safety measures in electrical systems as required by IEC 60364-6 (DIN VDE 0100-600) and other country-specific standards, and as specified in the individual sections of DIN EN 61557 (VDE 0413). [ more... ]

The test instrument makes testing in accordance with the following international standards possible:
IEC 60364, DIN VDE 0100, DIN VDE 0105, DIN EN 61557, CEI 64-8, ÖVE/ÖNORM 8001-6, NIV/NIN, CSN 33 2000-6, NEN 1010-6, GOST R (ГОСТ Р) 50571.16-99, IEC 61010

300 V 600 V PROFITEST INTRO

Working Efficiently Around the World

Intuitive operation
Measuring functions can be selected directly via the rotary switch
Background illumination
Help functions with wiring diagrams
International user interface (12 languages)
Universal connector system with country-specific measuring adapters for outlets
Measuring category: CAT III 600V / CAT IV 300V
Factory calibration certificate included

EASY transfer permits direct incorporation of test instruments from the
PROFITEST MASTER range into DDS-CAD planning software
.

Technical Characteristics [ more... ]

Measurement of R_LO, Z_L-PE, Z_L-N, R_INS, R_E, ΔU, rotary field, voltage

OFFSET management
Ohmic offset values R_L-PE, R_N-PE
and R_L-N can be ascertained and subtracted from the measured values for measurement of Z_L-PE, Z_L-N, R_E and ΔU( Z_L-N).
PE detection via finger contact
Measurement of touch voltage via finger contact When a measurement is started and if the ON/START key is touched with a finger, the test instrument detects whether or not dangerous touch voltage is present at the PE terminal relative to ground.
Low-resistance measurement for protective and equipotential bonding conductors with automatic polarity reversal
PRO-JUMPER for easy measurement cable compensation
Highly accurate measurement of internal system and fault loop impedance without tripping the RCD
Insulation measurement with rising ramp
Varistor response test with rising ramp and variable test current
Earthing resistance measurement (loop)
Voltage drop measurement

Voltage measurement, phase sequence, frequency measurement

A broad-range measuring device permits use of the test instrument in all alternating and 3-phase electrical systems with voltages from 65 to 500 V and frequencies of 15.4 to 420 Hz.

Testing of RCCB types
A, AC, F, B, B+, EV, MI and G/R, as well as SRCDs and PRCDs

Measurement of touch voltage without tripping the RCCB.
Touch voltage is measured with reference to nominal residual current using ? of the nominal residual current value.
RCD test with continuously rising ramp, time to trip, tripping current
Testing RCCBs with: ½×, 1×, 2×, 5× I_ΔN
Testing of RCCBs for pulsating residual direct current; testing is conducted with positive or negative half-wave

Communication and software

ETC software (Electrical Testing Center) for, amongst other functions, creating tree structures and documentation per ZVEH
Individual measured value memory for approx. 50,000 objects / measured values
Bidirectional data exchange via USB, DDS-CAD and epINSTROM
Connection of an RFID reader or a barcode scanner

Type comparison table

PROFITEST	INTRO	MBASE+	MPRO	MTECH+	MXTRA

RCD measurements
U_B measurement without tripping the RCD	x	x	x	x	x
Tripping time measurement	x	x	x	x	x
Tripping current measurement	x	x	x	x	x
Selective, SRCDs, PRCDs, type G/R	x	x	x	x	x
AC/DC sensitive RCDs, types B and B+	x	-	-	x	x
Testing of insulation monitoring devices (IMDs)	-	-	-	-	x
Testing of residual current monitoring devices (RCMs)	-	-	-	-	x
Testing for N-PE reversal	x	x	x	x	x
Loop impedance Z_L-PE / Z_L-N
Fuse table for systems without RCDs	x	x	x	x	x
Without tripping the RCD, fuse table	x	-	-	x	x
With 15 mA test current without tripping the RCD	x	x	x	x	x
Earth resistance
Earth resistance R_E (mains operation) I-U measuring method (2/3-wire measuring method via measuring adapter: 2-wire/2-wire + probe), (1 = without probe)	x(1)	x	x	x	x
Earth resistance R_E (battery operation) 3 or 4-wire measuring method via PRO-RE adapter	-	-	x	-	x
Soil resistivity ρ_E (battery operation) (4-wire measuring method via PRO-RE adapter)	-	-	x	-	x
Selective earth resistance R_E (mains operation) with 2-pole adapter, probe, earth electrode and current clamp sensor (3-wire measuring method)	-	x	x	x	x
Selective earth resistance R_E (battery operation) with probe, earth electrode and current clamp sensor (4-wire measuring method via PRO-RE adapter and current clamp sensor)	-	-	x	-	x
Earth loop resistance ρ_ELOOP (battery operation) with 2 clamps (current clamp sensor direct and current clamp transformer via PRO-RE/2 adapter)	-	-	x	-	x
Equipotential bonding measurement R_LO with automatic polarity reversal	x	x	x	x	x
Insulation resistance R_INS with variable or rising (ramp) test voltage	x	x	x	x	x
Variable or rising test voltage	x	x	x	x	x
Voltage measurement UL-N / UL-PE / UN-PE / f	x	x	x	x	x
Special measurements
Leakage current (clamp measurement) I_L, I_AMP phase sequence earth leakage resistance R_E(INS) voltage drop standing surface insulation Z_ST meter start-up	- x x x - -	x x x x x x	x x x x x x	x x x x x x	x x x x x x
Leakage current with PRO-AB adapter	-	-	-	-	x
Residual voltage test	-	-	-	-	x
Intelligent ramp	-	-	-	-	x
Features
Selectable user interface language	x	x	x	x	x
Memory (database for up to 50,000 objects)	x	x	x	x	x
Test sequence auto-function (programmable)	-	x	x	x	x
RS 232 port for RFID/barcode reader	x	x	x	x	x
USB port for data transmission	x	x	x	x	x
Interface for Bluetooth®	-	-	-	x	x
ETC user software for PC	x	x	x	x	x
Measuring category: CAT III 600 V / CAT IV 300 V	x	x	x	x	x
DAkkS calibration (2 = factory calibration certificate)	(2)	x	x	x	x
Article Number	M520T	M520S	M520N	M520R	M520P
PROFITEST	INTRO	MBASE+	MPRO	MTECH+	MXTRA

Video

Notice:

PROFITEST INTRO	Comment
Firmware ≥ V3.1.0	for software IZYTRONIQ
Firmware < V3.1.0	for ETC and other software

	Article No: M520T
	myGMC: News and informations about PROFITEST INTRO
	Technical Data » GB (pdf 669 kB)
	Operating Instructions » GB (pdf 1671 kB)
	Operating Instructions » E (pdf 1715 kB)
	Pamphlet » GB » F » PL » SF » RO (pdf 1156 kB)
	Short-form Operating Instructions (pdf 807 kB)
	Safety Information D-GB (pdf 142 kB)
	CE Certificate (pdf 35 kB)
	Software IZYTRONIQ
	Software ETC
	Software Driver Control
	Accessories (display)

1.	Z550A	Test Probe with Remote Triggering for METRISO and PROFITEST Series
2.	Z503F	Probes Set, CAT III @ 600 V, 1 A for PROFITEST Master
3.	F2010	Universal Carrying Pouch Big
4.	Z550C	Ever-ready Case for Testers
5.	SORTIMO L-BOXX	Plastic System Case for Testers and Accessories
6.	PRO-JUMPER	Adapter for measurement cable compensation, (DE) for PROFITEST INTRO
7.	PRO-JUMPER-CH	Adapter for measurement cable compensation, (CH) for PROFITEST INTRO
8.	PRO-JUMPER-GB	Adapter for measurement cable compensation, (GB) for PROFITEST INTRO
9.	PRO-SCHUKO-MA	Single-phase measuring adapter for PROFiTEST INTRO – for Germany
10.	PRO-CH-MA	Single-phase measuring adapter for PROFiTEST INTRO – for Switzerland
11.	PRO-GB-MA	Single-phase measuring adapter for PROFiTEST INTRO – for Great Britain
12.	KS-PROFITEST INTRO	Measurement cables for the PROFITEST INTRO
13.	Master Battery Pack	Rechargeable Battery Pack, welded
14.	Charger Z502R	Charger for Battery Pack - for PROFITEST, METRISO, SECULIFE IP
15.	PROFISCAN ETC	Barcode Entry Tool (CODE 128)
16.	Z502F	Barcode Scanner with Laser for Test Instruments with RS 232 Port
17.	Z751G	RFID Reader / Writer (13.56 MHz) for Test Instruments with RS 232 Port
18.	Z502Z	Magnetic Measuring Tips with Contact Protection - Set with Magnetic Holder
19.	A3-16	3-Phase Current Adapters for Test Instruments and 5-Pole CEE Outlets
20.	A3-32	3-Phase Current Adapters for Test Instruments and 5-Pole CEE Outlets
21.	A3-63	3-Phase Current Adapters for Test Instruments and 5-Pole CEE Outlets
22.	Vario Plugs	Variable Plug Adapter Set
23.	PRO-PE	Flat Test Clip, CAT IV @ 1000 V, 32A for PROFITEST Master
24.	Probe 1081	Floor Probe
25.	TR25-II	Plastic Drum with 25 m Measurement Cable
26.	TR50-II	Plastic Drum with 50 m Measurement Cable
27.	ISO-KALIBRATOR 1	Calibration Adapter for Insulation and Resistance Measuring Instruments
28.	PROFiSIM 1	Installation Board: "Service Line with Main Grounding Busbar" for Fault Simulation for Measurements per IEC 60364.6 (DIN VDE 0100-600) and EN 50110 (DIN VDE 0105-100) (new)
29.	PROFiSIM 2	Installation Board: "Sub-Distribution Branch with Installation Circuits" for Fault Simulation for Measurements per IEC 60364.6 and EN 50110 (DIN VDE 0100-600, 0105-100) (new)
30.	Telearm 120	Telescoping Rod for Measurement of PE and R_ISO, 120 cm
31.	Telearm 180	Telescoping Rod for Measurement of PE and R_ISO, 180 cm
32.	Z721E	Label Printer Prints Barcode Labels for Identifying Devices and Systems (new)

PROFITEST INTRO

Tester for DIN VDE 0100-600 / IEC 60364.6

Accessories (hide)

Catalogs T&M and Industry

Fairs and Product Shows

My Measuring Task

Video Streams

FAQs - FAQs - FAQs

Product Index